Volkswagen Jetta:

There are two screws on top of the lid, removed after the following panel fixing screws, pull out to see outside the frame of the fixed host two screws removed you can (do not lock off the machine).

Nissan Teana:

Decorate the two sides of the skid to open, there are four screws removed you can.

Regal:

First host on both sides of the curved mahogany bar first removed, then VII sleeve can be removed to the host.

New Mercedes-Benz S600:

1 meter before the middle of a small split-screen outlet, which has a wire gong; then split down the chassis switch (switch at the top with a wire gong); around the screen and then forced open the panel (of two) to see the screen There are two wire gong.

(2) first remove the bottom panel of the host (with leather package, the package must be good with tools, not the leather scratched), there are two wire gong; will cover the host's flip panel open, the top has two split wire gong , the frame can be out; host a four wire gong can be seen.

Hyundai Tucson:

First gears to tear down, and then forced open the bottom of the decorative box, see the screws, there are about ten, and then remove the iron frame of mind, and then pry the panel box, pry from the bottom up, and then saw six screws, remove the OK.

Mitsubishi Outlander:

First pull the cigarette lighter that quick trim, quick to pull the host plaque next to it (both clamp), you can see the four screws fixed the host.

Chevrolet Epica:

Host the edge of a block of cherry wood, look there are four gaps, the gap from the start, Alice can see the four screws to open.

Tiida:

1 dash above the first four lines forced open the lid.

(2) the audio from the following host pry decorative box.

3 Remove the four screws on both sides of the host, you can.

Fit 1.5CVT:

1 Remove the deputy side toolbox, broken air conditioning pull three

2 Remove the gearbox retaining plate (below the fuel tank / Note) Remove the glass tank.

3 Remove the ashtray

4 Remove the ashtray shield, unplug the cigarette lighter socket

5 ashtray guard has two screws inside the top of the symmetry, fixed up a central Car Audio panel

6 with a long flat head screwdriver from the toolbox (air conditioning cable) into his right side panel to open the two audio clips, the average force, the control panels and air conditioning knob will pop up with.

Carefully remove the host and the host pull the lower side of the air-conditioning, (after the operation should be carried out in three minutes after power failure)

After replacement of the host installation in reverse order! Transmission shield installed before the application of adhesive tape wrapped around a good protective effect, the construction workers asked all the screwdriver should be wrapped with insulating tape (to prevent short circuit)

Sound must be taken when purchasing this vehicle level is 80A, heavy-duty should not exceed!

1 to be split with tape to protect the host in the control panel, it's a bad Jiji classified

(2) below the storage box is not the original host off from the outside (behind the screw) is the correct way high power speaker and air conditioning knobs are one panel should be removed together

3 (key) then the best line of attack set fire to dry 4S shop, faithfully prepared in the absence of conditions before construction decoder must disconnect the power for 3 minutes (the original car relay) for operation. Should be received before the EU's main car insurance, because no power, the main Insurance burned.

Buick Hyundai Sonata:

Are forced open directly from the following

Lexus 300:

Split shift lever, then remove the two screws inside the armrest, won the central channel. Remove the ashtray, pull out the air conditioning switch system (straight out), then you can see the four screws removed.

Grand Cherokee 4700:

Forced open central air, like demolition of friends.

Fiat:

The third layer from the sound side Banxia start demolition, forced open the plaque shows the two air-conditioning switch panel screws, pull the air out of the bottom panel shows the two screws stereo, pull out the host directly.

m6:

From the box to the gear box is not the cup screws, ashtray with two screws, open the ashtray, the panel has two screws, open the glove box, remove the sleeve 10 with a screw, you can pull it to remove the nose;

Chery Eastar:

Careful observation of surface acoustic box with four small gap, with a pull on the wire into it can be, there are four classes screw, with 10 of the sleeve;

Son:

Pull out the outer decorative panels directly on the machine can see the screw up fixed.

Three Lingou Lan:

Have to remove the driving seat while two pull directly forced open, four screws;

Honda CRV:

Remove bottom two screws you can pull out;

Fit two boxes:

First remove the air below the button panel two screws, remove the decorative plates, and then cross with a long screwdriver from the bottom up inside the two screws removed, slowly pry open scraper with post film panel to see the host of the screws removed under OK.

Public:

There are dedicated keys fork into the can, no knife can also be used